Latexification 3 of 3

(Sorry for the wall of text. I encourage you to read it though...I've made it well worth your while! ^.-.~)

Looking down at his abdomen, over several minutes he saw the liquid slipping over his scales ever upwards, slowly crawling up to his chest. It tickled under his neck, and he instinctively tilted his head back. It flowed up his neck, and spread over his arms. Grunting as it crested his chin, he drew in a breath and held his air, closing his mouth. Unphased, the liquid still seeped into his mouth and through his nostrils, but the poor dragon still held his breath, closing his eyes. His lungs felt like they were about to burst, but he kept holding his breath until he just couldn't hold it any more.

He gasped for air, and at that instant the rest of the mysterious substance flooded into him, filling his lungs. He writhed, at first panickedly trying to draw air in, only further flooding his body with the liquid. But...

But he was still conscious, and...he wasn't coughing instinctively or even having to catch his breath from holding it so long. He...wait a second, he wasn't even breathing at all! He opened his eyes to see what had happened, and for a few moments he couldn't see due to a thick layer of the liquid over his eyes. His vision cleared over a few minutes as it soaked into him, and he looked to his left and right, seeing the liquid had taken over the rest of his arms and paws.

He wondered... “What happened? What....what AM I even?”

After a few more minutes, he noticed the liquid in the chamber seemed to be draining out, and then a spray of water from some nozzles above him cleaned him of excess liquid, revealing what was underneath. The dragon looked at his arms, and down at his belly and dragonhood, seeing them shine with a rubbery appearance. He gasped, stupified at the impossibility. His body was made of latex. He...was latex. The dragon felt lightheaded, and fainted.

PRESS RELEASE 9/23/2084: ZENNITH SCIENTIFIC INDUSTRIES announces the conclusion of several years of research into improving its lineup of “latex sex slave” products. Since 2081, Zennith SI has invested $7 billion USD in research and development of several technologies that are now being released to the market. Most importantly, we have perfected an enhanced latex bonding technique that has several advantages over our old technique.

Rather than simply tightening latex around a subject's body and sealing him in, we actually make the subject latex by 'soaking' him in a liquid latex solution, electrically charged, with a proprietary mix of chemicals enhancing latex uptake. The solution will freely climb and pervade any surface, and readily soaks through skin and deeply into the body. It will bind with cell membranes and replaces the extracellular matrix with a rubber polymer network.

The subject is restrained in a kneeling position in a pool of the latex solution. The latex climbs its way up the subject's body, crawling at first into his tailhole and urethra and eventually into all orifices. If the subject struggles, the latex only crawls up him faster, invading his recesses and body openings all the more efficiently. After a few minutes of soaking, the latex has fully binded to the subject's body. Excess is rinsed off with a pair of water nozzles. A computer-controlled low-power laser then colors the latex with an attractive, custom design caused by ultraviolet activation of a trace chemical dye.

The subject is still completely conscious, though constantly craves sex due to the “Reprogramming” procedure, performed after Latexification. A subject's biological activity is 93-97% reduced, and he will only need enough energy for his nervous system and some restricted movement. He can meet his minimal energy needs through any cum you give him, or (if you're not horny enough), IV injection. Any additional nutrition increases his energy levels substantially, so in effect the owner can chose how energetic their slave is at any time.

The body becomes much, much more flexible, with both flesh and bones uptaking latex. Rubber polymer networks replace calcium in bones. In general, the latex preserves the subject's appearance, though most features become a little softer, poofier, with small features becoming slightly exaggerated. Teeth are softened to the point of being rubberized nobs that harmlessly add texture to blowjobs.

The latex stiffens the subject's penis to a permanent semi-aroused state, always half-flaccid, dangling erotically. When aroused, the penis stiffens to its full length and girth, but is still flexible and squeezable, contouring to any tight holes it might be in.

The tailhole, and for that matter, the subject's entire insides become so stretchy and tight that the owner can stick anything from a finger to a 5 foot hyper-cock in the subject's tailhole; in any case we guarantee the fit will be perfectly warm and snug, and have a slippery, moist texture. Lubricant is never needed, because all surfaces are always a little moist, from the outside latexskin to the tightest internal spaces.

In fact, a variety of indulgences for your pleasure become possible that are otherwise nearly impossible. Inflation is perfectly possible; the subject can quite easily be inflated practically like a balloon without harm. An extremely stretchy urethra means you can please yourself any number of ways, from urethral fucking to even a sort of cock vore.

Regular vore is also very possible. If you are feeling particularly kinky, you can deny your slave food for a few days. He will attempt to eat anything around him, including you if you let him. Again, his teeth are completely rubberized, so he can only eat you whole. In this situation you would simply slide down his throat and squeeze through his rubbery insides. Any squirming will make him moan and convulse; he will collapse on the floor and spasm, inside and out, with his cock dripping with seeds for minutes to hours.

His seeds have a slicker consistency than natural semen, because of the presence of trace amounts of dissolved polymers. It makes for excellent lubricant, and he produces a -lot- of it.

Interested? You can contact our sales department at sales@zennith.com.

---

Well, that's that. This has been one of the bigger projects that I've worked on, and I really like how it turned out. I initially started this to be just one or two pictures, but I wound up drawing frame after frame which eventually turned into several pages...I just couldn't stop sketching! I finally limited myself to these images so I could actually get them done. I hope ya'll like/"enjoy" them!